Видео

발동된 상태 워드 0×208

How am I supposed to see what he’s doing with the camera across the room? 🙄 Zoom in!

Problem is when you take a large conductor and break it up into several smaller conductors, there is no protection for the smaller conductors except the upstream main OCPD. Which is going to be large enough for the whole system load.

Somebody should produce a "For Dummies" book for specific makes/models of VFD. I have this specific VFD, which has been set aside for several years. When I got it, I made pages of annotations. When I pulled it out again (still works), those notes were extremely valuable. The thick little book is incomplete and not perfect. Many of us aren't trying to automate a plant; we aren't trying to have various sensors adjust the motor. We just want a three phase motor to run on single phase. We need the VFD to run, stop, and reverse the motor. Braking might be useful, and variable speed would be icing on the cake. Even real, genuine factories may simply want to run "exactly what we need, but the wrong rpm" motor at 43hz. That horrible manual is truly an act of cruelty. But Hitachi, and other makers, are so proud of three or maybe four ways to control speed, they fail to mention the VFD is essentially locked out when it leaves the factory. Not explicitly mentioned in the printed manual. Oh yeah, the printed manual is not complete, you need to download the PDF... They suggest a crimper to attach ferrules to control wires. That crimper costs more than the VFD! You really do need a ferrule crimper, or maybe not. It seems terminal strip is impossible to access. Oh, I see, the removable access panel is EXACTLY THE SAME COLOR! And the cover that blocks the panel is EXACTLY the same color also! Oh, remove one screw, and, uh, oh, PRY IT OFF? yeah, sort of, it's also snapped on, besides the screw at the bottom right corner. Honestly, why not buy a cheap Chinese VFD and have exactly the same frustration for much less money? Or... Why not produce a simple VFD, and SPEND MONEY ON MAKING A COMPREHENSIBLE INSTALLATION MANUAL?

Wow what a worthless video thanks for nothing

pls be vegan animals also have lifes Radhe Radhe

Your video is not good explained not to show Claire

Do y’all expedite?

THIS IS NOT HOW ANYONE FAINTS.... THIS IS A BIO ORGANIC ROBOT THAT OUR ALIEN OVERLORDA PLACE IN EVERY POSITION OF POWER AND INFLUENCE TO DO THEIR BIDDING... every now and then they glitch out... I swear people are cringy slow about seeing what is right in front of them. In hindsight it will always seem more obvious. If you dont believe me google celebrity glitches with Shaq freezing up. and Cardi B...and whoever else....they also give us stupid explanations that only make sense.to a fellow robo...a human knows.how humans faint or have a brain fart...and its not the way a laptop glitches...

😅

Jean-Claude Jacquettie with his jacket on, Jean-Claude Jaquettie with his jack it off. Jacket On Jacket Off Jacket On Jacket Off

Nice design.... any links on schematics? Just asking. Thanks

Seems like more of a infomercial than a tutorial. RUclips DIYers explain things better.

Why thank you

Great video tutorial very informative and easy to understand, Thank you for sharing your knowledge,❤️🇵🇭

amazing video ❤✌

Measuring 10000 ohm resistance in my windshield wiper motor. Set range to mohm and get ol. Does this mean that the wire is cut. When I put it into continuity there is no beep. So the wire is cut? Thanks.

Could FLIR explain why they designed the probe holders on the back in such a way that you cannot put both Red and Black probes in the upward position and therefore be able to use it to test wall sockets or panel terminals with just one hand? PeakTech 1700 doesn't have this issue, Megger DCM330 doesn't have this issue, Benning CM 1-4 doesn't have this issue, IDEAL 61-415 doesn't have this issue, only the Fluke T5 and T6 have this issue, so maybe FLIR should stop taking inspiration from them?

Is there a way to keep the cap from sticking i cracked the cap😂 need to know for future purposes

Try applying it to very small screws. Real sticky mess. I want to love it though

❤

Yo she bad

it would have been even better if you had shown the settings on the multimeter for ohms, continuity etc

As i spin the brush motor with my hand i cant help but notice a fraction noise, should i lube it?

It sounds like is about to cumbust

Is the 50/100% neutral setting a % of the L dip switch setting or the breaker maximum or 50/100% of something else?

Where on the Ohmmeter do you turn the knob to? Very bad explanation

Replaced the 9v battery and now the display doesn’t show anything

Does anyone know how to wire/ program in an external start/ stop switch to this?

Do these come in 100% rated or just 80% rated?

How to change in language

👍👍👍👍👍

not clear explanation

This voice might be fit for some yoga mat commercial but is definitely wrong for the electrical field. Makes me wanna go through my warehouse look for anything from this brand and toss it into a dumpster.

Amigo me puedes ayudar tengo un P1000 y no me lee la presion de la tuberia, me podrias ayudar con los parametros para activarlo ya que antes si los leia solo que alguien que no debia metio la mano y lo desconfiguro

Where can I download the software to connect with this Power Factor Controller?

I use these a lot. Good quality components

Amazing

what is the default password for the Setra SRPM?

Queria a tradução desse vídeo

Pls change the language

I have replaced the c2000 drive but the motor is running in reverse, how do I change the direction?

Indiot, is mov connected only via live or neutral line?

How do you recover active programming after you read program 1?

This is an excellent "womansplaining" 🥂 ..if only she had a brain. The world went to hell when women were allowed to vote. Auto fuses can be tested with a multimeter without being removed. - I'm so disgusted.

Parash?

Parash

The federal signal 350’s are loud af. Yikes.

OL is defined as Overload in Fluke Manual

whats with the accent at end of the words 😂